Which furniture production machine should a new workshop buy first?

A new furniture workshop should normally buy the sliding table panel saw first, because the panel saw sizes every part and sets the accuracy of everything that follows. The edge banding machine is the usual second purchase, the boring machine the third, and a CNC router is added when parts stop being rectangular. A beam saw only makes sense once sheet volume, rather than the operator, limits output.

What is the difference between a panel saw and a beam saw?

A sliding table panel saw is operator-paced: the operator loads a single sheet on the carriage and pushes it through the blade, so a panel saw is flexible and suits mixed one-off work. A beam saw clamps a stack of panels and cuts programmed strips through the whole book, so a beam saw suits repeat production. This category lists 29 panel saws and 3 beam saws.

What power supply do furniture production machines need?

Most furniture production machinery in this category needs a three-phase 400 V supply, and only the smallest machines are available for single-phase power. Confirm the incoming supply, the main breaker rating and the cable run with an electrician before a panel saw, edge banding machine, beam saw or CNC router is ordered, and tell us your available supply when you request a quotation so the machine is specified to match.

How much floor space and extraction does this equipment need?

Floor space for furniture production machinery is set by panel movement, not by machine footprint: a sliding table panel saw needs its full carriage stroke clear at both ends plus sheet width beside the blade, and an edge banding machine needs infeed and outfeed length for your longest panel. Extraction must be sized to the number of open ports on each machine, and CNC routers also need vacuum clamping for the table.

What determines the price of furniture production machinery?

The price of furniture production machinery is determined by configuration: sliding table length, motor power and scoring unit on panel saws; the number of working stations on edge banders; table size, spindle power and tool changer on CNC routers. Tooling - blades, cutters, drill bits and glue - is budgeted separately, as are delivery to site and commissioning. Send your part sizes and volumes and we will quote against them.

Do you supply tooling and consumables with the machine?

Tooling and consumables for furniture production machinery are quoted separately from the machine itself, because the correct saw blade, scoring set, cutter, drill bit, glue type and edge tape depend on the material you cut. Tell us the boards and tape you use when you request a quotation and the tooling package will be listed as its own line so the machine arrives ready to run.

Furniture Production Machinery

77 machines

Sort Power: high to low

Beam Saws Boring and Mortising Machines CNC Routers Edge Banding Machines Sliding Table Panel Saws

Machines found

To order

MIZRAK OF-KA TUANA 56 Edge Banding Machine
Edge Banding Machines

Workpiece Thickness

8 – 54 mm

Working Speed

14 m/min

Air pressure

6 – 8 atm
To order

MIZRAK OF-KA TUANA 56 PREMIUM Edge Banding Machine
Edge Banding Machines

Workpiece Thickness

8 – 60 mm

Working Speed

14 – 18 m/min

Air pressure

6 – 8 atm
To order

MIZRAK ROYAL 8 EXTRA Edge Banding Machine
Edge Banding Machines

PC control with a servo-driven pre-tracer is the highest control level Mizrak fits to an edge bander, and the ROYAL 8 EXTRA is the machine carrying that package: infrared pre-heating, a sensor-fed motorised glue pot and disc-tracer milling for 0-3 mm tape. Mizrak publishes no capacity table for the ROYAL 8 EXTRA.
To order

MIZRAK TUANA 56 X PLUS Edge Banding Machine
Edge Banding Machines

PC control with a servo-driven pre-tracer is what sets the TUANA 56 X PLUS apart from the PLC-screen OF TUANA 56. Published units cover jumping pre-milling, infrared pre-heating, a sensor-fed glue pot, pneumatic top pressure, angled end cutting and 0-3 mm disc-tracer milling; Mizrak publishes no technical table for the TUANA 56 X PLUS.
To order

NETMAK CNC 2411 CNC Router and Door Machining Centre
CNC Routers

Working area

2400 mm

Spindle

12000-24000 rpm

Overall dimensions

3200 x 1750 x 2400 mm

Furniture Production Machinery — in brief

Furniture production machinery covers the machines that turn full sheets of chipboard, MDF, plywood and faced board into finished cabinet parts: sizing, edge finishing, drilling and shaped machining. This category holds 77 machines from HOLZMANN (Austria), MIZRAK and NETMAK (Turkey), grouped as sliding table panel saws (29), edge banding machines (28), CNC routers (10), boring machines (7) and beam saws (3). The range starts at a one-operator joinery bench and reaches a factory line. Every machine here is supplied by quotation, configured to your voltage, panel sizes and tooling before pricing.

Furniture Production Machinery

Machines found

MIZRAK OF-KA TUANA 56 Edge Banding Machine

MIZRAK OF-KA TUANA 56 PREMIUM Edge Banding Machine

MIZRAK ROYAL 8 EXTRA Edge Banding Machine

MIZRAK TUANA 56 X PLUS Edge Banding Machine

NETMAK CNC 2411 CNC Router and Door Machining Centre

Furniture Production Machinery — in brief

Filter

Saved machines

Your saved list is empty