What carriage length should a sliding table panel saw have?

Choose the carriage length of a sliding table panel saw from the largest panel you cut in one pass. Under 2000 mm - the HOLZMANN TS250FL, TS250F, TS250F1600, TS315F1600, FKS305V16TOP and the MIZRAK MZK 1500 PRESTIJ - suits doors, cabinet parts and pre-cut board in a crowded shop. 2000-2800 mm handles half sheets and long rips. 3200 mm takes a standard full sheet lengthwise in one uninterrupted pass and is the usual cabinet-shop choice, while 3800 mm models handle oversize sheets and door leaves.

Is there a panel saw that works on single-phase 230 V?

Yes. Most sliding table panel saws on this page are 400 V three-phase machines, but the HOLZMANN TS315F1600 is offered in a 230 V single-phase version as well as a 400 V three-phase version, and the TS315VF2600 is the one scoring sliding table saw here that can be ordered as 230 V single-phase, with a 100 mm cut at 90 degrees and a 2600 mm carriage. If the workshop has no three-phase connection, those two models are the starting point; otherwise, budget the electrical installation with the machine.

How much floor space and extraction does a panel saw need?

A sliding table panel saw needs roughly twice its carriage length along the line of cut, because the carriage travels fully forward and fully back, plus the width of the outrigger table and room for the operator to walk the panel round. A 3200 mm saw therefore wants a clear run of about six and a half metres, and a 3800 mm machine more. Extraction connects at the blade hood and the lower cabinet; a scoring saw cutting faced board produces fine dust that a shop extractor or cyclone unit should handle continuously.

Do I need the scoring unit on a panel saw?

A scoring unit is effectively required on a panel saw if the shop cuts melamine, laminated or veneered board, because the scorer cuts the lower face a fraction ahead of the main blade and prevents the underside chipping out. On this page scoring is 0.75 kW on the MIZRAK saws and 750 W on the FKS305 models, with a 100 mm scorer at 8500 min-1 on the TS315VF3200. For solid timber and unfaced material the scorer matters less, but almost every furniture workshop will use it daily.

What makes one panel saw more expensive than another?

On a sliding table panel saw the price is driven by carriage length, frame weight, main saw power, and above all the setting method. The MIZRAK PRESTIJ saws are hand-set; the SPECIAL and Diamond S add motorised tilt and blade rise; the Diamond SX adds PLC control with a servo cast-iron rear stop; the Concord adds a 5.5 kW drive, pneumatic hold-down and a digital fence. On the HOLZMANN side the FKS400V32PRO adds motorised rip-fence positioning over the FKS400V32SMART and FKS400V32TOP. Blades, extraction, delivery and installation are quoted alongside, so every model here is priced by configuration.

What is the difference between the MIZRAK PRESTIJ, SPECIAL, Diamond, Diamond S, SX and Concord saws?

The MIZRAK panel saw families differ mainly by how the machine is set, not by cutting capacity - PRESTIJ, SPECIAL, Diamond and Diamond S all cut 80 mm at 90 degrees with a 4 kW saw motor and 0.75 kW scorer. PRESTIJ is fully hand-set; SPECIAL and Diamond S add motorised 45-90 degree tilt and motorised blade rise; Diamond SX adds PLC control and a servo linear cast-iron rear stop; Concord moves to a 5.5 kW main saw with automatic tilt, pneumatic panel hold-down and a digital cast-iron fence. Choose the level of automation your batch sizes justify, then choose 3200 or 3800 mm of travel.

Sliding Table Panel Saws

29 machines

Sort Recommended

Beam Saws Boring and Mortising Machines CNC Routers Edge Banding MachinesSliding Table Panel Saws

Machines found

To order

MIZRAK MZK 3800 Diamond S Sliding Table Panel Saw
Sliding Table Panel Saws

Table Size

550 x 910 mm

Weight

860 kg
To order

MIZRAK MZK 3800 Diamond Sliding Table Panel Saw
Sliding Table Panel Saws

Table Size

550 x 910 mm

Weight

770 kg
To order

MIZRAK MZK 3800 Diamond SX Sliding Table Panel Saw
Sliding Table Panel Saws

Table Size

550 x 910 mm

Weight

700 / 780 / 790 kg
To order

Mizrak MZK 3800 PRESTIJ Sliding Table Panel Saw
Sliding Table Panel Saws

Table Size

550 x 910 mm

Weight

740 kg
To order

Mizrak MZK 3800 SPECIAL Sliding Table Panel Saw
Sliding Table Panel Saws

Table Size

550 x 910 mm

Weight

808 kg

Sliding Table Panel Saws — in brief

A sliding table panel saw sizes sheet material by carrying the panel past the blade on an aluminium carriage, with a scoring blade ahead of the main blade to stop the faced underside chipping. This category covers 29 saws from HOLZMANN and MIZRAK, with carriage travel from 1320 mm on the HOLZMANN TS250FL to 3800 mm on the MZK 3800 PRESTIJ, Diamond, SPECIAL and Concord models, blades from 250 to 400 mm, and setting methods from fully manual to PLC control with a servo rear stop. All models are supplied by quotation.

Sliding Table Panel Saws

Machines found

MIZRAK MZK 3800 Diamond S Sliding Table Panel Saw

MIZRAK MZK 3800 Diamond Sliding Table Panel Saw

MIZRAK MZK 3800 Diamond SX Sliding Table Panel Saw

Mizrak MZK 3800 PRESTIJ Sliding Table Panel Saw

Mizrak MZK 3800 SPECIAL Sliding Table Panel Saw

Sliding Table Panel Saws — in brief

Filter

Saved machines

Your saved list is empty