Skip to main content
+995 577 44 44 34
Request a call

Edge Banding Machines

28 machines

Sort Name
Beam SawsBoring and Mortising MachinesCNC RoutersEdge Banding MachinesSliding Table Panel Saws
Sort Name

Machines found

Edge Banding Machines — in brief

An edge banding machine glues tape to the cut edge of a panel and then trims, scrapes and polishes it in one pass. This category covers 28 machines from HOLZMANN and MIZRAK across three classes: hand-guided 230 V banders such as the KAM50M and KAM65PRO, the stationary powered-feed KAM535NEO, and automatic one-sided lines from the 3.62 kW MIZRAK ADVANTAGE-3 and HOLZMANN KAM35P up to the PC-controlled ROYAL 8 EXTRA and TUANA 56 X PLUS. Panel capacity runs from 8-42 mm to 8-60 mm and feed speed from 2 to 18 m/min. Every machine is sold by quotation.

Decide the class before the model: hand-guided, powered-feed or automatic

Three classes of edge bander sit on this page, and the class decides most of the price. Hand-guided HOLZMANN machines – the 3 kg KAM50M, the 855 W KAM45PRO, the 765 W KAM55V and the KAM65PRO at 8.8 kg – run from a single-phase 230 V socket and are steered along the panel by the operator, which suits site work, repairs, curved fronts and low volume. The HOLZMANN KAM535NEO is the middle class: a stationary 400 V bander with its own 250 W feed at 0-15 m/min, a 1000 x 700 mm table and a 20 mm minimum inside radius. Everything above is an automatic one-sided machine with a chain conveyor and a fixed sequence of units.

The unit list, not the brand, sets the price

On an automatic edge bander the fitted units decide both quality and cost. Pre-milling recuts the sawn edge before glue is applied and is exactly what separates the MIZRAK MZK-4 at 4.02 kW from the OF MZK-4 at 7.02 kW with its 1.5 kW cutter at 12,000 rpm, and the HOLZMANN KAM35EP from the KAM35ESV. Automatic front and rear end cutting is the step the ADVANTAGE X SMALL has and the ADVANTAGE-3 does not. Scraping and polishing decide how the edge looks after trimming; corner rounding removes hand work on radiused fronts, to 36 mm on the ADVANTAGE-6 and to 42 mm on the OF-KA TUANA 56 PREMIUM; and a 2.6 kW grooving unit cuts the back-panel groove on the same pass, fitted to the ADVANTAGE-7 and the OF-KA TUANA 56 but not to the OF TUANA 56.

Panel thickness, tape and feed speed

Panel capacity separates the ranges cleanly: 8 to 42 mm on the HOLZMANN KAM4EPS and across the MIZRAK ADVANTAGE line, 8 to 54 mm on the MZK 4 and TUANA 56 machines, and 8 to 60 mm on the OF-KA TUANA 56 PREMIUM. Tape runs 0.4 to 3 mm. Feed speed is throughput rather than finish: 7 m/min on the KAM35P, 10 m/min across the ADVANTAGE range, 13 m/min on the KAM215 machines, 14 m/min on the MZK 4 family and 20 m/min on the flying-cut OF-KA MZK 4 WIND.

Power supply, floor length and extraction

Power supply splits this page in two. The portable HOLZMANN banders work on single-phase 230 V, while every automatic machine is a 400 V three-phase installation, from 3.62 kW on the ADVANTAGE-3 to 19.38 kW on the OF-KA TUANA 56 PREMIUM, so check the connected load of the exact model against the shop supply. Floor length is the frame length plus infeed and outfeed for the longest panel: 2500 mm for the ADVANTAGE-3, 3500 mm for the ADVANTAGE-4, 4900 mm for the ADVANTAGE-6 and 5900 to 7180 mm across the TUANA 56 machines. Trimming and pre-milling throw fine chip at every unit, so extraction is required; the KAM4EPS carries integrated dust collection and the ADVANTAGE-4 integrates extraction, while the longer machines connect to the shop system.

Entry, middle and top of the range

Control level is what the top of the range buys. The ADVANTAGE-3 and KAM35P are manually set entry machines; the TUANA 56 models add PLC screen control; the TUANA 56 X PLUS and ROYAL 8 EXTRA move to PC control with a servo pre-tracer, infrared pre-heating and a sensor-fed glue pot. Budget separately for EVA glue granulate, edge tape, spare trimming cutters and scraper blades, compressed air, extraction, delivery and installation; those, with the unit list and panel capacity, drive every quotation.

How to choose

  1. Machine class

    Hand-guided 230 V machines (KAM45PRO, KAM50M, KAM55V, KAM65PRO) for site work, repairs and curved fronts; the KAM535NEO for steered stationary work; automatic lines for daily cabinet output.

  2. Pre-milling unit fitted or not

    Specify pre-milling when panels arrive with saw marks or from a nesting router: OF MZK-4 (7.02 kW) instead of MZK-4 (4.02 kW), KAM35ESV instead of KAM35EP.

  3. Panel thickness 8-42, 8-54 or 8-60 mm

    8-42 mm covers standard cabinet board (ADVANTAGE line, KAM4EPS); 8-54 mm on the MZK 4 and TUANA 56 machines takes thick fronts and doors; 8-60 mm only on the OF-KA TUANA 56 PREMIUM.

  4. Corner rounding

    Order corner rounding if fronts are radiused - to 36 mm on the ADVANTAGE-6 and to 42 mm on the OF-KA TUANA 56 PREMIUM. Without it every corner is dressed by hand.

  5. Grooving unit

    A 2.6 kW grooving unit on the ADVANTAGE-7 or OF-KA TUANA 56 cuts the back-panel groove during banding and removes a separate saw setup; the OF TUANA 56 has no grooving unit.

  6. Feed speed 2-20 m/min

    2-6 m/min on hand-guided units, 7-10 m/min for a joinery shop, 13-14 m/min on the KAM215 and MZK 4 machines, 20 m/min on the flying-cut OF-KA MZK 4 WIND for continuous batches.

  7. Frame length 2500-7180 mm

    Add infeed and outfeed for the longest panel to the frame length: 2500 mm ADVANTAGE-3, 3500 mm ADVANTAGE-4, 4900 mm ADVANTAGE-6, 5900-7180 mm across the TUANA 56 machines.

  8. Control level

    Manual setting on the ADVANTAGE-3 and KAM35P; PLC screen control on the TUANA 56 machines; PC control with a servo pre-tracer on the TUANA 56 X PLUS and ROYAL 8 EXTRA.

Frequently asked questions

How do I choose between the HOLZMANN and MIZRAK edge banding machines?
Choose an edge banding machine by class first, then by unit list. Hand-guided HOLZMANN machines (KAM45PRO, KAM50M, KAM55V, KAM65PRO) work on 230 V for repairs, curved fronts and site work; the KAM535NEO adds a powered 0-15 m/min feed and a table; the automatic machines from the KAM35P and ADVANTAGE-3 upward add pre-milling, end cutting, scraping, corner rounding and grooving in a fixed sequence. Set the panel thickness you band (8-42, 8-54 or 8-60 mm) and the units you need, and the shortlist reduces to a few models.
What power supply do edge banding machines need?
Edge banding machines split by power supply: the portable HOLZMANN units - KAM45PRO at 855 W, KAM55V at 765 W, KAM50M at 2000 W and the KAM65PRO - run on single-phase 230 V, while every automatic bander here is a 400 V three-phase machine. Connected load rises from 3.62 kW on the MIZRAK ADVANTAGE-3 and 3960 W on the HOLZMANN KAM35EP to 12.68 kW on the OF-KA TUANA 56 and 19.38 kW on the OF-KA TUANA 56 PREMIUM, so confirm the load of your chosen model against the workshop supply before ordering.
How much floor space and extraction does an edge bander need?
An edge bander needs its frame length plus infeed and outfeed space for the longest panel handled, with room to walk both sides. Frames run from 2500 mm on the ADVANTAGE-3 and 2060 mm on the KAM35P up to 4900 mm on the ADVANTAGE-6 and 5900-7180 mm on the TUANA 56 machines. Extraction is required because pre-milling and trimming produce fine chip at each unit; the HOLZMANN KAM4EPS has integrated dust collection and the MIZRAK ADVANTAGE-4 integrates extraction, while the longer machines are connected to the shop extraction system.
Do I really need a pre-milling unit on an edge bander?
A pre-milling unit is worth specifying on an edge banding machine when panels arrive with saw marks, slight chipping or a not-quite-square edge, because pre-milling recuts the edge immediately before glue is applied and improves the glue line. Pre-milling is exactly what separates the MIZRAK MZK-4 (4.02 kW, no pre-milling) from the OF MZK-4 (1.5 kW cutter at 12,000 rpm, 7.02 kW) and the HOLZMANN KAM35EP from the KAM35ESV. If panels are cut on a well set scoring panel saw and banded immediately, a machine without pre-milling can still give a clean result.
What determines the price of an edge banding machine?
The price of an edge banding machine is driven by the unit list (pre-milling, end cutting, trimming, scraping, corner rounding, grooving), panel and tape capacity, feed speed, control level and frame length - a manually set ADVANTAGE-3 and a PC-controlled ROYAL 8 EXTRA are different machines, not different discounts. Add the tooling and consumables package: EVA glue granulate, edge tape, spare trimming cutters and scraper blades, compressed air, extraction, plus delivery, installation and operator training. Every model on this page is quoted individually, so send your panel sizes and volumes with the request.
Can these machines band curved fronts and radiused panels?
Yes, but the class of edge bander decides how. The handheld HOLZMANN KAM50M bands both straight and curved workpieces, and the stationary KAM535NEO follows an inside radius down to 20 mm while its own 250 W feed pulls the panel past the glue pot. Automatic one-sided machines band straight edges only; for radiused fronts what matters there is a corner rounding unit, fitted to 36 mm on the MIZRAK ADVANTAGE-6 and to 42 mm on the OF-KA TUANA 56 PREMIUM, which removes hand dressing of the corners after banding.